Micro simulated moving bed chromatography-mass spectrometry as a continuous on-line process analytical tool.

Continuous manufacturing is becoming increasingly important in the (bio-)pharmaceutical industry, as more product can be produced in less time and at lower costs. In this context, there is a need for powerful continuous analytical tools. Many established off-line analytical methods, such as mass spectrometry (MS), are hardly considered for process analytical technology (PAT) applications in biopharmaceutical processes, as they are limited to at-line analysis due to the required sample preparation and the associated complexity, although they would provide a suitable technique for the assessment of a wide range of quality attributes. In this study, we investigated the applicability of a recently developed micro simulated moving bed chromatography system (µSMB) for continuous on-line sample preparation for MS. As a test case, we demonstrate the continuous on-line MS measurement of a protein solution (myoglobin) containing Tris buffer, which interferes with ESI-MS measurements, by continuously exchanging this buffer with a volatile ammonium acetate buffer suitable for MS measurements. The integration of the µSMB significantly increases MS sensitivity by removing over 98% of the buffer substances. Thus, this study demonstrates the feasibility of on-line µSMB-MS, providing a versatile PAT tool by combining the detection power of MS for various product attributes with all the advantages of continuous on-line analytics.

Development of a 3D printed micro simulated moving bed chromatography system.

In the 1960s, chromatography processes were revolutionized by the invention of simulated moving bed chromatography. This method not only enhances the separation performance and resin utilization in comparison to batch-chromatography, it has also a much lower buffer consumption. While simulated moving bed chromatography nowadays is applied for a wide range of industrial applications, it was never transferred to the micro-scale (in regards to column and system volume). In our opinion a micro simulated moving bed chromatography system (µSMB) would be a useful tool for many applications, ranging from early process development and long term studies to downstream processing of speciality products. We implemented such a µSMB with a 3D printed central rotary valve and a microfluidic flow controller as flow source. We tested the system with a four zone open loop setup for the separation of bovine serum albumin and ammonium sulfate with size exclusion chromatography. We used four process points and could achieve desalting levels of BSA ranging from 94% to 99%, with yields ranging form 65% to 88%. Thus, we were able to achieve comparable results to common lab scale processes. With a total dead volume of 358 µL, including all sensors, connections and the valve, this is, to the best of our knowledge, the smallest SMB system that was ever built and we were able to perform experiments with feed flow rates reaching as low as 15 µL/min.

Configurable 3D Printed Microfluidic Multiport Valves with Axial Compression.

In the last decade, the fabrication of microfluidic chips was revolutionized by 3D printing. It is not only used for rapid prototyping of molds, but also for manufacturing of complex chips and even integrated active parts like pumps and valves, which are essential for many microfluidic applications. The manufacturing of multiport injection valves is of special interest for analytical microfluidic systems, as they can reduce the injection to detection dead volume and thus enhance the resolution and decrease the detection limit. Designs reported so far use radial compression of rotor and stator. However, commercially available nonprinted valves usually feature axial compression, as this allows for adjustable compression and the possibility to integrate additional sealing elements. In this paper, we transfer the axial approach to 3D-printed valves and compare two different printing techniques, as well as six different sealing configurations. The tightness of the system is evaluated with optical examination, weighing, and flow measurements. The developed system shows similar performance to commercial or other 3D-printed valves with no measurable leakage for the static case and leakages below 0.5% in the dynamic case, can be turned automatically with a stepper motor, is easy to scale up, and is transferable to other printing methods and materials without design changes.

Multi-attribute PAT for UF/DF of Proteins-Monitoring Concentration, particle sizes, and Buffer Exchange.

Ultrafiltration/diafiltration (UF/DF) plays an important role in the manufacturing of biopharmaceuticals. Monitoring critical process parameters and quality attributes by process analytical technology (PAT) during those steps can facilitate process development and assure consistent quality in production processes. In this study, a lab-scale cross-flow filtration (CFF) device was equipped with a variable pathlength (VP) ultraviolet and visible (UV/Vis) spectrometer, a light scattering photometer, and a liquid density sensor (microLDS). Based on the measured signals, the protein concentration, buffer exchange, apparent molecular weight, and hydrodynamic radius were monitored. The setup was tested in three case studies. First, lysozyme was used in an UF/DF run to show the comparability of on-line and off-line measurements. The corresponding correlation coefficients exceeded 0.97. Next, urea-induced changes in protein size of glucose oxidase (GOx) were monitored during two DF steps. Here, correlation coefficients were ≥ 0.92 for static light scattering (SLS) and dynamic light scattering (DLS). The correlation coefficient for the protein concentration was 0.82, possibly due to time-dependent protein precipitation. Finally, a case study was conducted with a monoclonal antibody (mAb) to show the full potential of this setup. Again, off-line and on-line measurements were in good agreement with all correlation coefficients exceeding 0.92. The protein concentration could be monitored in-line in a large range from 3 to 120 g L- 1. A buffer-dependent increase in apparent molecular weight of the mAb was observed during DF, providing interesting supplemental information for process development and stability assessment. In summary, the developed setup provides a powerful testing system for evaluating different UF/DF processes and may be a good starting point to develop process control strategies. Graphical Abstract Piping and instrumentation diagram of the experimental setup and data generated by the different sensors. A VP UV/Vis spectrometer (FlowVPE, yellow) measures the protein concentration. From the data of the light scattering photometer (Zetasizer, green) in the on-line measurement loop, the apparant molecular weight and z-average are calculated. The density sensor (microLDS) measures density and viscosity of the fluid in the on-line loop.

Automated Solid-Phase Protein Modification with Integrated Enzymatic Digest for Reaction Validation: Application of a Compartmented Microfluidic Reactor for Rapid Optimization and Analysis of Protein Biotinylation.

Protein modification by covalent coupling of small ligands or markers is an important prerequisite for the use of proteins in many applications. Well-known examples are the use of proteins with fluorescent markers in many in vivo experiments or the binding of biotinylated antibodies via biotin-streptavidin coupling in the frame of numerous bioassays. Multiple protocols were established for the coupling of the respective molecules, e.g., via the C and N-terminus, or via cysteines and lysines exposed at the protein surface. Still, in most cases the conditions of these standard protocols are only an initial guess. Optimization of the coupling parameters like reagent concentrations, pH, or temperature may strongly increase coupling yield and the biological activity of the modified protein. In order to facilitate the process of optimizing coupling conditions, a method was developed which uses a compartmented microfluidic reactor for the rapid screening of different coupling conditions. In addition, the system allows for the integration of an enzymatic digest of the modified protein directly after modification. In combination with a subsequent MALDI-TOF analysis of the resulting fragments, this gives a fast and detailed picture not only of the number and extent of the generated modifications but also of their position within the protein sequence. The described process was demonstrated for biotinylation of green fluorescent protein. Different biotin-excesses and different pH-values were tested in order to elucidate the influence on the modification extent and pattern. In addition, the results of solid-phase based modifications within the microfluidic reactor were compared to modification patterns resulting from coupling trials with unbound protein. As expected, modification patterns of immobilized proteins showed clear differences to the ones of dissolved proteins.